Academy
Geometry

Geometry Settings

Flip chips, dropouts, headset cups and wheel sizes — one frame, several geometries

What are geometry settings?

A geometry setting is a part of the frame or headset you can change after the frame is built, so one frame gives you more than one geometry.

One frame, its settings highlighted: flip chip, dropout, headset cupsacademy.geo-settings.hero

A frame's geometry is fixed by its tubes, but a few joints can be built so that they have more than one position. Change the position and the whole bike sits differently: the bottom bracket moves up or down, the head angle opens or closes, the rear wheel moves back or forward. Brands add these settings so a single frame can be tuned for a trail, a park or a race day, for a different wheel size, or for a rider between two sizes.

What makes settings tricky is that nothing changes on its own. Lowering the bottom bracket also slackens the head angle and the seat angle, shortens the reach and raises the stack a little — because the whole bike pivots about its rear tire contact until both wheels are back on the ground.

Flip chip
Moves a pivot or the shock mount
Dropout
Moves the rear axle
Headset cups
Change head angle or reach
Wheels
Change ride height front or rear

Flip chips

A flip chip is a small insert with an off-centre hole. Turned around, it moves a pivot by a few millimetres — and the whole bike follows.

Flip chip high / low — the same frame in both positionsacademy.geo-settings.flip-chip
Typical travel of a flip chip: 4–8 mm at the pivot

Most flip chips sit at the shock mount or at a linkage pivot. Moving that point changes where the linkage rests at sag, so the rear end sits lower or higher. On a full-suspension bike the effect at the bottom bracket is usually 5–10 mm, and the head angle changes by about half a degree.

  • 1Low: lower bottom bracket, slacker head and seat angle — more stability, more pedal strikes.
  • 2High: higher bottom bracket, steeper angles — more clearance and a more lively feel.
  • 3On many bikes the chip also changes the leverage curve slightly, because the linkage starts from another position.
What 'low' does: BB drop, head angle, seat angle — numbers on the drawingacademy.geo-settings.flip-chip-effect
All changes come from one pivot moving a few millimetres
🔑 Key Concept
A flip chip belongs to an element of the linkage. If the chip sits where the rocker meets the swingarm, it can be part of either — and that decides which element changes its shape and which keeps it. BikeSPEZL's kinematic editor asks for exactly that.

Adjustable dropouts

Adjustable dropouts move the rear axle, usually to make the rear centre longer or shorter.

Adjustable dropout: short / long rear centre, chainstay length markedacademy.geo-settings.dropout

A longer rear centre makes the bike calmer at speed and keeps the front wheel down on climbs; a shorter one makes it easier to lift and turn. Some frames move the axle only backwards, others also up or down — a dropout for a smaller rear wheel lifts the axle so the bottom bracket keeps its height.

  • 1Back / forward: rear centre (chainstay) length, typically ±5–10 mm.
  • 2Up / down: compensates a smaller wheel; a lower axle drops the bottom bracket.
  • 3On a full-suspension bike the axle path and anti-squat change too.
Δz = (622 − 584) / 2 = 19 mm   (rim bead seat diameters)

Axle height a 27.5'' dropout must make up on a 29'' frame

Headset cups: angle, reach, VPP

Headset cups change the front of the bike without touching the frame: the steerer sits at an angle or off-centre.

Angle-adjust cups: ±1° head angle, the fork rotating about the lower cupacademy.geo-settings.headset-angle

Angle-adjust cups hold the steerer tube at an angle to the head tube — commonly ±0.5° to ±2°. A slacker head angle makes the bike more stable in steep terrain; a steeper one makes it quicker to steer. Because the bike pivots about its rear contact, the seat angle changes by roughly half as much, the other way round.

Reach-adjust (offset) cups and VPP: the steerer moved forward / backacademy.geo-settings.headset-reach

Reach-adjust or offset cups move the steerer forward or back without changing its angle — a few millimetres of reach for a rider between sizes. VPP-style cups combine an offset with a choice of mounting direction, so the same cups can add or take away reach, and they also change the fork offset the front wheel sees.

  • 1Angle cups: head angle ±°, seat angle ∓ about half of that.
  • 2Reach cups: reach ± a few mm, stack almost unchanged.
  • 3VPP cups: reach and effective fork offset change together — trail changes as well.

Wheel sizes and mullet

A different wheel size is the biggest setting of all: it changes the ride height at that end of the bike.

Mixed wheels: 29'' front / 27.5'' rear — the rear drops, the bottom bracket lowersacademy.geo-settings.mullet

A 27.5'' rear wheel on a 29'' frame lowers the rear axle by about 19 mm. After the bike settles onto both wheels again, the bottom bracket is lower and the head and seat angles are slacker — the classic mullet setup. Frames built for it either accept the change or make up for it with a flip chip or a dropout.

ℹ️ Note
Tire size matters too: a taller tire raises its end of the bike by half its extra height. BikeSPEZL measures wheel sizes by the rim's bead seat diameter, so 29'' (622 mm), 27.5'' (584 mm) and 26'' (559 mm) always mean the same.

Settings per size

Not every size of a frame has every setting — small sizes often come with a smaller rear wheel only.

Size table: which setting each size offersacademy.geo-settings.size-specific

A brand might offer a 27.5'' rear wheel only on the two smallest sizes, or a dropout position only on the largest. Each size then has its own list of settings — and its own geometry in each of them.

Geometry settings in BikeSPEZL

Set them up once on the geometry card; every section that references it sees the same settings.

Screenshot: the geometry editor's Settings tab with its setting tilesacademy.geo-settings.editor
  • 1Geometry editor → Settings: one tile per position (Base first, + to add). Click a tile to use it, right-click to edit its values or switch it on for some sizes only.
  • 2Kinematic editor: the flip chip is placed on an element of the linkage; the solver re-assembles the linkage so the chip's new position and the bench pose meet again — before the bike is levelled onto the ground.
  • 3Every change is levelled: the bike rotates about the rear tire contact until both wheels touch the ground, then every number you see is measured.
  • 4R&D and the fit tools use the selected setting, so the rider fit, the loads and the characteristics all follow it.